- Research article
- Open Access
Molecular analysis of meso- and thermophilic microbiota associated with anaerobic biowaste degradation
BMC Microbiology volume 12, Article number: 121 (2012)
Microbial anaerobic digestion (AD) is used as a waste treatment process to degrade complex organic compounds into methane. The archaeal and bacterial taxa involved in AD are well known, whereas composition of the fungal community in the process has been less studied. The present study aimed to reveal the composition of archaeal, bacterial and fungal communities in response to increasing organic loading in mesophilic and thermophilic AD processes by applying 454 amplicon sequencing technology. Furthermore, a DNA microarray method was evaluated in order to develop a tool for monitoring the microbiological status of AD.
The 454 sequencing showed that the diversity and number of bacterial taxa decreased with increasing organic load, while archaeal i.e. methanogenic taxa remained more constant. The number and diversity of fungal taxa increased during the process and varied less in composition with process temperature than bacterial and archaeal taxa, even though the fungal diversity increased with temperature as well. Evaluation of the microarray using AD sample DNA showed correlation of signal intensities with sequence read numbers of corresponding target groups. The sensitivity of the test was found to be about 1%.
The fungal community survives in anoxic conditions and grows with increasing organic loading, suggesting that Fungi may contribute to the digestion by metabolising organic nutrients for bacterial and methanogenic groups. The microarray proof of principle tests suggest that the method has the potential for semiquantitative detection of target microbial groups given that comprehensive sequence data is available for probe design.
Anaerobic digestion (AD) is a microbiological process where organic material is degraded by numerous different groups of microorganisms . The AD process consists of three main steps. First, the complex organic material is hydrolysed. Then, in acidogenesis and acetogenesis, the generated less complex substrates are converted into acetate, hydrogen and carbon dioxide from which methane is finally produced in methanogenesis . At least four different trophic groups are essential for methanogenic degradation: 1) fermentative heterotrophs decompose organic materials such as proteins, lipids and carbohydrates, 2) proton-reducing H2-producing heterotrophic syntrophs are involved in degradation of small molecules like fatty acids and ketones, and, 3) H2-utilising and 4) aceticlastic methanogenic archaea produce the methane .
Biowaste used as a substrate for AD contains different organic materials from food crop residues to waste originating from industrial processing. The microbial community present in the AD process is largely determined by the substrate composition  and reactor design as well as operating conditions . One of the important operating conditions is temperature which affects the microbial diversity of the AD process drastically: in mesophilic (temperature about 35 °C) conditions, the species richness and the number of different microbial phyla appear to be higher and the species composition very different compared to thermophilic (temperature about 55 - 60 °C) conditions. Nevertheless, the AD reactor performance is relatively similar in both temperatures, except for the more efficient degradation of some specific organic compounds and the presence of pathogens at higher temperatures [5, 6]. However, a temperature exceeding 64 °C has been observed to cause acetic acid build-up and process failure leading to diminished methane production .
While the abundance and distribution of Bacteria and Archaea in AD processes are well characterised [4, 6, 8–11], the analysis of Fungi present in the process has been largely overlooked. Fungi are typically discussed in studies of AD only as a potential source of pathogens like Aspergillus without considering their possible role in digestion. It has been reported that the total number of fungal colony forming units is not reduced during the AD process in either mesophilic or thermophilic reactors, but still the number of fungal genera is significantly decreased . However, there are known aerobic microbial e.g. fungal groups present in anaerobic digesters originating from the substrate . The aerobic groups stay viable and can therefore form colonies when plated, which may cause biased results when using culturing methods to measure the microbial abundance and distribution . Hence, analysis of phylogenetic marker gene sequences would provide a more reliable characterisation of the composition of microbial communities in the AD process. Our aim in this study was to reveal the molecular phylogenetic structure of bacterial and archaeal and also the fungal communities in AD process operating at different temperatures and organic loads using 454-pyrosequencing. Furthermore, we utilised the 454 sequence data to evaluate a DNA microarray method for monitoring the microbiota in the AD process. Such DNA microarray technology could enable a rapid, almost on-line monitoring of the microbial situation in the process and the digestate reject waters, when needed. Hygienisation of solid and liquid products of the process could also be confirmed without causing delays to the further handling of the products.
Anaerobic reactor and test runs
The pilot scale anaerobic digestion (AD) reactor has been previously described in detail . In brief, the AD reactor was a completely stirred tank reactor (200 L; operating volume of 150 L) which was fed semi-continuously (once per day) with a mixture of biowaste and sewage sludge (30% and 70% of total wet weight, respectively). The reactor was first run in a mesophilic temperature range of 35 - 38 °C, and later in a thermophilic range of 52 - 56 °C. The organic loading rate (OLR) was increased stepwise from 1 to 10 kgVS m-3d-1 (kg volatile solids per m3 reactor volume and day) (Figure 1). At the same time, HRT (hydraulic retention time) was decreased stepwise from 58 days to 8 days. The selected AD process parameters of the test runs are presented in Tables 1 and 2. The total solids (TS%) were determined by drying samples at 105 °C. The volatile solids (VS%) were determined by volatilizing the organic matter in a muffle oven for 2 h at 550 °C. The alkalinity and total amount of volatile fatty acids (VFA) were determined by a titration method . First the sample was titrated to pH 4 (alkalinity), then to pH 3.3 at which the sample was boiled to release CO2. The amount of VFAs was determined by back titration with NaOH from pH 4 to pH 7.
Sampling protocol and DNA extraction
Sampling for DNA isolation was done in transient AD reactor conditions, i.e. at the load-increasing points: from 2 to 3 kg VS m-3d-1, and from 5 to 8 kg VS m-3d- both in the mesophilic (M1 and M2) and thermophilic (M3 and M4) runs (Table 3). HRT values for each sampling are given in Table 1. The sample volume of the AD reactor’s digested sludge was 1 mL. Total DNA was extracted from the whole volume (4 x 250 mg) of the samples with FastDNA Spin Kit for Soil according to manufacturer’s instructions (MP Biomedicals, France). Extracted DNA was visualised in agarose gel and the concentration of DNA was measured with NanoDrop ND-1000 spectrophotometer (Thermo Fisher Scientific, Waltham, MA, USA). Prior to use, DNA was stored at −20 °C.
The PCR amplification of the sample DNA was conducted with MJ Research PTC-225 thermal cycler (Global Medical Instrumentation) in two stages. First, we amplified the DNA with universal bacterial, archaeal and fungal primers in following conditions: initial denaturation at 94 °C for 5 min, 20 cycles of 94 °C for 30 s, 60 °C for 30 s and 72 °C for 2 min, and a final extension for 5 min with bacterial and archaeal primers (Table 4). With fungal primers the applied annealing temperature was 55 °C. In the first round we used eight replicate reactions per sample and pooled and purified the reactions before the second round. In the second round, the amplification was completed with 10 additional cycles with sample-specific barcode sequences and A- and B-adapters attached to the primers. Each sample was amplified in three replicates. The amount of template varied between 200 ng and 700 ng per reaction (volume 50 μl) depending on sample and primers. The PCR amplifications were carried out in the first round with Phusion (Finnzymes, Espoo, Finland) (Bacteria) and Biotools (Biotools, Madrid, Spain) (Archaea and Fungi), and in the second round with Truestart (Fermentas, Lithauen) DNA polymerases. After the amplifications, the replicates were pooled and the PCR-products were processed as described previously . The sequencing was carried out at the Institute of Biotechnology (Helsinki, Finland) using the 454 GS FLX protocol, yielding read length of about 250 bp (454 Life Sciences, Roche Diagnostics, CT, USA).
Sequence data processing
The sequence data was sorted into libraries according to sample-specific barcode sequences using Ribosomal Database Project’s Pyrosequencing pipeline Initial Process  and thereafter the tag and the primer sequences were removed. We also left out sequence reads less than 100 bp in length, or with one or more ambiguous nucleotides (N) in order to use only good quality sequences in further analysis . The sequences that passed the initial quality control were analysed with Mothur . Bacterial and archaeal sequences were aligned to SILVA alignment database . Aligned sequences were preclustered, distance matrices were prepared and the sequences were clustered to operational taxonomic units (OTUs) using average neighbor algorithm. Rarefaction curves ( Additional file 1) and ACE  and Chao1  indices (Table 3) were calculated to estimate the community richness, and Simpson and Shannon indices  were used in assessing the diversity present in samples. We also calculated Venn diagrams and dendrograms describing the shared OTUs within samples and similarity between the structures of communities, respectively. The dendrograms were constructed using the Yue & Clayton similarity value, θYC. Fungal sequences were aligned and distance matrix was prepared using Mothur pairwise.seqs command. Clustering and other downstream analyses were carried out as with Bacteria and Archaea. Taxonomic affiliations were determined with BLAST  and Megan : sequence reads were queried against the NCBI nucleotide database (nr/nt)  and the results were analysed using Megan. Fungal sequences affiliated to Plantae or Animalia were removed from the dataset. We applied Ribosomal Database Project’s Classifier  to determine the bacterial and archaeal groups present in samples. The sequences have been deposited in the Sequence Read Archive (SRA) at EBI with study accession number ERP000976. The most abundant microbial groups are presented in Figure 2.
Redundancy analysis (RDA) ordination technique [35, 36] was used to explore the relationships between microbial community composition and variation in physical and chemical parameters. Microbial composition data from both sequencing and microarray were used as dependent variables and six selected physico-chemical parameters as constraints. Only the 12 most abundant microbial classes from sequencing and 12 strongest microarray probes were included in the analysis. Correlation coefficients were used as inertia in the model and plotting. Three different constraining variables were used per analysis because the number of constraining variables is restricted to n-1 (n referring to the number of observations; here M1-M4). Analyses were done using R-software package vegan v. 1.17-12 .
Ligation probe design
We designed a set of probes consisting of sequences matching to common fungal and bacterial phylotypes (42 probes) and another set that matched OTUs from AD amplicon data (47 probes) ( Additional file 2). The design of ligation probes was based on identification of target-specific nucleotide positions by using sequence alignments and NCBI's Primer-BLAST. First, for those target reads that matched with at least 94% similarity to a full length 16 S rRNA gene in NCBI database, the corresponding 16 S sequences were collected and incorporated into a Greengenes prokaryote 16 S reference database . The minimum length cutoff in the Greengenes database was 1250 bp. A second alignment was constructed of the short pyrosequencing reads representing OTUs. For both alignments, an algorithm that screens for single nucleotide differences was implemented in R-software  using Biostrings package . If a specific nucleotide position was identified for a given target sequence, the 3' end of discriminating ligation probe was set to match that position. If no such site was found, Primer-BLAST at the NCBI website was employed to find probe candidates for that target sequence. In Primer-BLAST, the nr/nt database was used as reference and primer stringency settings included at least two non-target mismatches in the last four nucleotides in the 3' end. Finally, the Tms of selected probes were set to 60 °C and 64 °C for the discriminating and common parts, respectively, using thermodynamic nearest neighbour calculation in Oligocalc software . A schematic of the technique is presented in Figure 3.
Probe library preparation
The custom oligo library was synthesised by Agilent (Santa Clara, CA) at 10 pmol scale. The dried oligo library, containing 70 fmol of each probe, was dissolved into 70 μl of water and aliquoted to 7 X 10 μl. An aliquot was phosphorylated in a reaction containing 1X PNK buffer A (Fermentas,Lithauen), 0.5 mM ATP and 1 μl of PNK (Fermentas, Lithauen) in a 20 μl volume. The reaction was incubated at 37 °C for 45 min followed by inactivation at 65 °C for 10 min. 30 μl of 0.1X TE buffer was added for final volume of 50 μl and concentration of 400 amol/μl/probe.
In order to validate the probes, we designed 96 oligonucleotide templates each consisting of two partially overlapping 50-mer parts. To produce 80-mer double stranded templates from the two oligos, a fill-in reaction containing 1X TrueStart buffer (Fermentas,Lithauen), 1.33 mM MgCl2 (Fermentas, Lithauen), 200 μM of each dNTP, 1.6 U of TrueStart Taq DNA polymerase (Fermentas, Lithauen) and 10 μM of both oligos in a 20 μl volume was performed. The program consisted of activation step at 95 °C for 3 min and 5 cycles of denaturation at 95 °C for 30 s, annealing at 55 °C for 30 s and extension at 72 °C for 15 s. Final extension was 15 min at 72 °C. Template oligo sequences are listed in Additional file 3. Ninety-six templates were divided into four pools and each pool was tested separately with all of the probes on the microarray.
Ligation reactions were carried out in a 10 μl volume containing 1X Pfu ligase buffer (Agilent Technologies, Santa Clara, CA, USA), herring sperm DNA (Sigma-Aldrich, Steinheim, Germany), 30 mM tetramethylammonium chloride (TMAC; Sigma-Aldrich, Steinheim, Germany), about 200 ng of environmental template DNA, 400 amol of each probe and 2 U of Pfu ligase (Agilent Technologies, Santa Clara, CA, USA). The reaction was cycled for 20 rounds at 94 °C for 30 s and at 56 °C for 8 min in a thermal cycler (MJ Research, MA, USA).
PCR from ligated probes
The PCR reaction mixture for amplification of circularised ligation products contained 1X Paq HS buffer (Agilent Technologies, Santa Clara, CA, USA), 200 μM of each dNTP, 0.5 μM forward primer (5'-Cy3-CGACGTTGTAAAACGACGGCCAGT-3'), 0.5 μM reverse primer (5'-phosphate-TTTCACACAGGAAACAGCTATGAC-3'), 2.5 U of Paq5000 DNA polymerase (Agilent Technologies, Santa Clara, CA, USA) and 10 μl of ligation reaction in a final volume of 30 μl. The PCR program consisted of activation step at 95 °C for 3 min and 35 cycles of denaturation at 95 °C for 20 s, annealing at 58 °C for 14 s and extension at 72 °C for 5 s. The PCRs were done in Arktik thermal cycler (Finnzymes, Espoo, Finland) with block-mode temperature control using manufacturer's PCR tubes.
The microarray experiments were performed on Arrayit or Agilent microarray platforms. The 16 compartment slides purchased from Arrayit (Sunnyvale, CA, USA) were designed and used as described previously . Briefly, for hybridisation to Arrayit microarrays, a mixture containing 20 μl of PCR/lambda exonuclease reaction, 5X SSC, 20 μg of herring sperm DNA (Sigma-Aldrich, Steinheim, Germany) and 5 pmol of control oligo in a final volume of 60 μl was applied to each subarray according to manufacturer's instructions. The hybridisation was carried out in the dark at 55 °C for 2 h. After hybridisation, the microarray was washed for 3X15 min in 0.1X SSC, 0.1% SDS and briefly with water. Finally, the slide was air dried. The high-density custom oligo microarrays were manufactured by Agilent (Santa Clara, CA, USA) in 8 X 15 K format. Each of eight subarrays contained 1500 cZipCode oligos in ten replicates. Hybridisation to Agilent microarrays was performed according to manufacturer's instructions. Briefly, hybridisation mixture containing 1X GEx hybridisation buffer (Agilent Technologies, Cedar Creek, TX, USA), 1X GEx blocking reagent (Agilent Technologies, Cedar Creek, TX, USA), 18 μl of PCR/lambda reaction and 5 pmol of control oligo was applied on each subarray and hybridised for 17 h in the dark at 65 °C at 10 rpm rotation. The slide was washed with Gene Expression wash buffer 1 (Agilent Technologies, Wilmington, DE, USA) for 1 min at RT and Gene Expression wash buffer 2 (Agilent Technologies, Wilmington, DE, USA) for 1 min at 37 °C. 10% Triton X-102 was added to both washing solutions to final concentration of 0.005%. The fluorescent signals were detected at 5 or 10 μm resolution using a GenePix Autoloader 4200AL laser scanning system with green laser for Cy3 dye (ex 543 nm/em 570 nm) and blue laser for 6-FAM (ex 488 nm/em 495 nm). The laser power was set at 100% and the photomultiplier (PMT) tube was adjusted according to the intesity of the signal. GenePix program version 6.1 was used to quantitate the signal from each spot. The microarray data is included in Additional files 456.
Microarray data analysis
The microarray data were managed using R-software  and Bioconductor package marray. The microarray raw signals were processed as described previously . Briefly, after local background subtraction, the control channel values were multiplied by the ratio of medians of probe channel and control channel. Next, negative values were removed and probe channel signals were adjusted as Li' = Lilog(Li/Ci), where Li is the raw probe channel signal value at feature i and Ci is the adjusted control channel signal value at feature i. Further normalisation in sensitivity tests with Arrayit microarrays was executed by dividing all signals by a control ligation probe signal. Alignment of probe sequences to template sequences was done in R using local pairwise alignment functions from package Biostrings. The used nucleotide substitution matrix had match score of 1 and mismatch score of −2. The microarray data have been deposited to ArrayExpress with accession numbers E-MEXP-3539 (sensitivity tests), E-MEXP-3541 (reactor samples), E-MEXP-3538 (specificity tests).
Quantitative PCR experiments
A TaqMan probe (5'-AGGAACATGTGGTTTA-3') was designed to hybridise to the same position as the corresponding microarray ligation probe (A123). The probe harbored a 5' VIC® reporter dye, a 3' non-fluorescent quencher and a MGB™ (minor groove binder). The PCR reaction mixture for amplification of the TaqMan probe target region contained 1X Genotyping Master Mix (Applied Biosystems, Foster City, CA, USA), 900 nM forward primer (5'-GAAAGCGATAAGTTATCCACCTGGG-3'), 900 nM reverse primer (5'-TTCGAGCCCGGGTAAGGTTCC-3'), 250 nM TaqMan probe and approximately 50 ng of environmental DNA in a final volume of 20 μl. The PCR program consisted of activation at 95 °C for 10 min and 40 cycles of denaturation at 95 °C for 30s and annealing/extension at 60 °C for 1 min. Each reaction had three replicates in the assay plate. The reaction was carried out in StepOnePlus realtime PCR instrument (Applied Biosystems, Foster City, CA, USA).
Results and discussion
Anaerobic codigestion of biowaste and sewage sludge was performed with organic loading rates from 1 to 10 kg of VS m-3 d-1 in in mesophilic (M1 and M2) and thermophilic (M3 and M4) conditions. In the steady state conditions, i.e. the biogas production is not changed over time due to the load increase but has reached a constant level, the biogas production at the load of 3 kg VS m-3 d-1 was 680 and 760 liters kg-1VS-1 in the mesophilic and thermophilic runs, respectively (Table 2). In both temperatures the specific biogas production was lower at the loads of 5–8 kgVS m-3d-1 than that with 3 kg VS m-3d-1load. The CH4 concentration varied between 61.7 -68% in the both runs. The amounts of trace gases, especially ethanol and ammonia, increased in the thermophilic conditions.
Overview of microbial diversity in AD
Selected samples from the outfeed of meso- (M1 and M2) and thermophilic (M3 and M4) pilot AD reactors at the loading rates of 3 and 5–8 kg VS m-3d-1 were subjected to microbial diversity analysis using 454 rRNA gene amplicon deep sequencing. A total of 77 189 sequences out of 83 975 sequence reads were classified based on BLASTN results. The total number of sequence reads that passed quality check ranged from 2 000 in Bacteria to almost 17 000 in Fungi per sample (Table 3). Figure 2 summarises the most abundant archaeal, bacterial and fungal groups present in the samples. Rarefaction analysis (Additional file 1) revealed that the fungal diversity increased together with increasing loading rate and decreasing retention time during the experiment, and Chao1 and Ace [27, 28] richness estimates supported this observation (Table 3). In Bacteria, the trend in rarefaction analysis was the opposite, thus declining during the digestion process. Richness estimates in the mesophilic process backed up this result whereas in the thermophilic conditions the numbers were contradictory (Table 3). In Archaea, the diversity decreased during the experiment in the mesophilic and increased in the thermophilic reactor (Table 3). Several studies have shown that mesophilic AD process carries more microbial diversity than thermophilic process and that temperature affects the community composition of microbial communities [6, 44–49]. In this study, rarefaction analysis (Additional Figure 1), richness estimates and diversity indices (Table 3) indicated approximately equal diversity in both temperatures. However, at class and genus level more bacterial classes and genera and archaeal genera were found in the mesophilic reactor than in the thermophilic reactor. Based on UPGMA (Unweighted Pair Group Method with Arithmetic mean) clustering  (data not shown), the bacterial and archaeal communities were more similar between the mesophilic samples (M1 and M2) than the thermophilc samples (M3 and M4), suggesting that bacterial and archaeal communities in the study reactors were strongly driven by temperature. In contrast, the fungal communities became more pronounced during the digestion process: the M1 and M3 samples taken in the beginning of the experiment from different reactors were more similar to each other than to M2 and M4 samples, suggesting that organic loading rate is a more important factor in determining the fungal community structure than the process temperature. As the digester was a completely stirred tank reactor, the new feed material is constantly mixed with old material while the mixture is being washed out. The operating time span before sampling was over one HRT in samples M1 and M3 and slightly less one HRT in samples M2 and M4 (Table 1, Figure 1). Due to constant stirring, this difference is not likely to have a major effect on the reactor microbiota. The minimum HRT used in this study was 9–10 days which is approximately the same as the generation time of methanogens and other microbial groups and as such is sufficient for proper decomposition of organic material. The efficiency of the degradation was also illustrated by the fact that no accumulation of degradation intermediates, i.e. VFA, occurred.
The mesophilc (M1 and M2) and thermophilic (M3 and M4) samples contained in total 15 bacterial phyla. Most commonly found bacterial phyla included Bacteroidetes Firmicutes and Thermotogae, constituting 47%, 24% and 9% of all bacterial sequence reads, respectively. The phylum Bacteroidetes was more abundant in the mesophilic reactor, and the bacterial classes of Flavobacteria Sphingobacteria and Bacteroidia were found solely from the mesophilic reactor. Clostridia and Bacilli, the two classes of Firmicutes, were detected in both reactors but were more prevalent in thermophilic conditions, and Thermotogae was detected exclusively in the thermophilic reactor. Different classes of Proteobacteria and Actinobacteria were found in thermophilic conditions in quite small numbers, but these groups were substantially more abundant in the mesophilic reactor. Spirochaetes Synergistes and Verrucomicrobia were present only in the mesophilic reactor. We also detected several bacterial phyla comprised merely of environmental clones including OP8, OP11, SR1 and TM7. Somewhat concordant results regarding the heterotrophic bacteria in anaerobic digestors have been published before [51–54]. Bacterial phyla Bacteroidetes Firmicutes and Thermotogae are often found in both mesophilic and thermophilic AD processes which reflects their importance in degradation of complex organic compounds .
Bacterial genera frequently encountered in AD include Spirochaeta sp., Clostridium sp., Propionibacterium sp., Thermotoga sp., Arthrobacter sp. and Bacillus sp. . In the present study, 7% of all bacterial sequence reads were classified to genus level. All in all, we identified a total of 19 bacterial genera. The most common bacterial genus was Clostridium, present in all samples but more abundant in the thermophilic reactor. Genus Clostridium contains species that are capable of anoxic digestion of cellulose and fermenting amino acids, and these bacteria are commonly found in different types of anaerobic digesters . In several earlier studies members of order Clostridiales have been detected to represent a dominant fraction of bacterial communities in AD and these bacteria are recognised important in biogas production [56–58]. Coprothermobacter sp. and Syntrophomonas sp. were also relatively common, with Coprothermobacter found solely in thermophilic and Syntrophomonas in both reactors.
We were able to identify 89% of all archaeal reads at phylum level and 34% at genus level. All the Archaea classified at phylum level belonged to phylum Euryarchaeota. This is in agreement with other descriptions of archaeal composition of anaerobic sludge where Euryarchaeota clearly dominate over Crenarchaeota, and orders Methanosarcinales and Methanomicrobiales are known to represent an eminent proportion of the Archaea present . The two identified methanogenic classes were Methanobacteria and Methanomicrobia. These methanogens were found at both temperatures, although Methanobacteria were more prevalent in the thermophilic conditions (M3 and M4) than in the mesophilic conditions (M1 and M2). These classes represent typical archaeal constituents in methanogenic AD systems . We identified also six different archaeal genera in our dataset based on BLAST against nr/nt database. Methanosarcina was very abundant, and slightly more common in the mesophilic process. Methanobrevibacter Methanosphaera Methanospirillum and Methanosphaerula were abundant in mesophilic digestor (M1 and M2), while Methanobacterium was detected merely in thermohilic digestor (M3 and M4). In agreement with our study, Goberna and co-workers also found an increase of Methanobacteria in thermophilic AD . Several studies have shown that Methanosarcina sp., Methanococcus sp. Methanoculleus sp., Methanomethylovorans sp. and Methanobacterium are typically found in anaerobic digesters [4, 6, 8–11].
We identified 85% of the fungal sequences at phylum level and 44% at genus level. The Fungi detected in our study belonged to two phyla, Ascomycota and Basidiomycota. The sequence reads assigned to Ascomycota represented almost 99% of the fungal sequences and consequently, Basidiomycota constituted about 1% of the fungal reads. Saccharomycetes and Eurotiomycetes were the most abundant fungal classes in the whole dataset, constituting 58% and 12% of the fungal sequence reads, respectively. These classes were found in both temperatures, with Saccharomycetes being more abundant in the thermophilic digestor (M3 and M4) and Eurotiomycetes in the mesophilic digestor (M1 and M2) (Figure 2). A total of 33 fungal genera were detected. By far the most abundant was Candida, found in both processes at both samplings, but especially prevalently in the thermophilic reactor. The second most common fungal genus, Penicillium, was present in all samples but notably more thriving in the mesophilic reactor where it constituted the majority of all fungal sequence reads. The third most common fungus Mucor was found in all samples as well, but it seemed to prefer elevated thermophilic temperatures. In fact, several fungal groups, like Zygorhynchus Cladosporium and Pseudeurotium were found solely in the thermophilic conditions, whereas for example Rhizomucor Geotrichum and Trichosporon were found exclusively in the mesophilic reactor. The relative abundance of fungal groups like Pichia Saccharomyces Aspergillus Mucor and Candida increased during the digestion process, indicating that these fungal groups not only tolerate the conditions in the reactors but may actually benefit from them. Pichia and Candida are also associated in aerobic digestion . Schnürer and Schnürer  recently studied fungal survival in anaerobic digestion of household waste and found out that mesophilic temperature did not reduce the amount of culturable fungal colony forming units in the waste, and that thermophilic conditions caused only a slight decrease in the number of fungal viable cells. This phenomenon was not detected in our study, but actually the thermophilic digestor (M3 and M4) contained more fungal diversity in both samplings compared to the mesophilic digestor (M1 and M2, Figure. 2). The majority of Fungi are aerobic, but a wide range of them are able to grow in low oxygen conditions. There are also fungi that can survive and grow in anaerobic conditions if an appropriate nutrient source is available. The fungal genera Candida Mucor Penicillium Saccharomyces and Trichoderma, detected in our study, are facultative anaerobes and as such capable of degrading organic material in anoxic environment [62–64]. Thus, these groups can potentially not only survive the anaerobic conditions but also actively contribute to the process by decomposing more complex organic compounds such as lignin and cellulose in the beginning of the degradation.
Functional validation of the microarray probes
Microarray as a high-throughput platform has the potential for routine microbial analysis of environmental samples [65–67], although detection accuracy of oligomeric probes targeting phylogenetic marker gene may present a challenge in analysing complex communities consisting of a large number of closely related genomes . Assaying the microbial composition in the AD process would be valuable for in-process monitoring of the microbial content and confirming hygienisation of the end product. To that end, we applied ligation probes that circularize upon target recognition (“padlock probes”) and are subsequently amplified and hybridised on microarray by unique tag sequences (Figure. 3). In principle, the method enables detection from unamplified source material and has been previously successfully used for plant pathogen detection on qPCR  and microarray platforms  as well as for gene variant analysis [70, 71]. However, to our knowledge, this type of technique has not been applied to profiling complex microbial communities to date.
Here, we tested a set of padlock probes to evaluate the potential of the method for AD process monitoring and more generally for microbial community analysis (Figure 4). In order to establish the functionality and target sequence specificity of the probes, we used 10 fmol of probe-specific synthetic dsDNA oligos as templates for the probe pool in ligation reactions. Signals from the subset of probes corresponding to the templates present in each pool could be clearly distinguished from signals from the rest of the probes (Additional file 4), suggesting a good target sequence specificity. However, the signal intensities of different probes varied considerably at the constant 10 fmol template concentration, probably because of random variability of PCR  and sequence bias of ligation [73, 74]. Approximately 10% of the probes were not functional despite their perfect alignment to template. Six probes were non-specific giving false positive signals, despite that they did not have good alignment to any of the templates. To estimate the amount of detectable template, we tested template pools each containing 24 templates, at four different concentrations each. The probe signal intensities correlated with concentration (Additional file 5) with the highest concentration (1 fmol/μl/template) giving the highest signals while at the lowest concentration (0.001 fmol/μl/template) practically none of the probes produced detectable signals. Almost all of the probes had consistently lower signals with lower concentrations and the majority of probes were still detectable at 0.01 fmol/μl/template concentration, suggesting that the method may be used for semiquantitative assaying over at least three orders of magnitude.
Microarray analysis of the AD samples
To evaluate the microarray’s capability in analysing the AD samples, we performed ligation reactions using about 200 ng of non-amplified sample DNA as template for the probe pool. The microarray signals from the mesophilic samples M1 and M2 and the thermophilic samples M3 and M4 grouped separately and along the gradients of physical and chemical parameters in a similar way as with sequencing data (Figure 5) in redundancy analysis . This suggests that our microarray had the ability to monitor changes in the microbial community structure in response to conditions of the digestor, an important aspect of in-process monitoring of AD status. However, while the grouping with M1 and M2 was comparable to sequencing data, M3 and M4 clustered less clearly separately showing that the microarray was not as accurate in classifying samples as deep sequencing with regard to process loading rate. The reason for this could be that most of the microarray probes did not show detectable signals. The probes were initially designed to match certain phylotypes or phylotype-level OTUs (97% read sequence similarity), but as these typically corresponded to relatively few sequences in the sample material, the target sequence abundances were likely to be below detection limit of the method. Also, specific microarray probes could not always be designed merely on the basis of trimmed 454 sequence reads due to their limited length of 150 nt, which necessitated us to retrieve full-length rRNA genes matching to OTUs from the NCBI nucleotide database. The closest matching gene to an OTU was typically only 94% similar, leaving considerable uncertainty regarding the estimated target specificity of the probes in the context of the AD sample DNA. Probe sequence alignments against the most abundant full-length database rRNA genes identified in the samples showed that many of the probes indeed did not have good matches. As expected under the probe-target sequence mismatch hypothesis, the probes that could be aligned with mismatches to the database rRNA genes were less accurate (Additional file 6) than 100% matching probes. Since the probes in the initial specificity tests responded highly accurately to their cognate target oligo pools, it is reasonable to assume that at least some missing signals are explained by unknown sequence differences in the rRNA genes. Secondary structures inherent to rRNA sequences are one possible contributor to probe target recognition  as well. However, we found complementarity within the probe pool only between two sequences (data not shown), but this does not completely rule out the possibility of dimerisation between other probes too, as alignment cannot fully explain oligo hybridisation behaviour. However, with 100% match to target sequences the signals were more consistent. Figure 4 shows microarray signals of a probe matching to several full length rRNA genes of uncultured bacterial groups, and corresponding relative number of 454 reads of these targets. The signals correlated with read number and TaqMan RT-qPCR signals obtained using the same probe sequence, thus verifying the microarray results. This proof of principle data suggests that the microarray method is capable of semiquantitative assaying of target microbial groups, provided the target sequences constitute at least 1% of total DNA in the sample as measured by amplicon sequence reads. Furthermore, the results show that sensitivity of the padlock method is clearly better compared to the traditional ligation detection reaction (LDR), which requires PCR amplification of the target sequences first, and is not able to detect targets directly from source DNA .
Our results show that both the mesophilic and thermophilic AD process contain a prominent fungal community that survives and grows in anoxic conditions. This suggests that Fungi may metabolise organic nutrients for subsequent use by archaeal and bacterial methanogenic groups, thus contributing to the digesting process and biogas production. The microarray proof of principle testing showed the capability of the technique to profile the microbial composition of AD samples. According to our results, the microarray method is capable of semiquantitative analysis of AD process when comprehensive sequence information is available to support probe design. We expect future metagenomic sequencing of the total genomic content in these environments to enable more accurate probe design and, together with RNA sequencing, to help determining the ecology and metabolic functions of various fungal and other microbial groups present in the AD community.
Hobson P, Wheatley A: Anaerobic digestion: Modern Theory and Practice. 1993, Elsevier, London
Zehnder AJB: Ecology of methane formation. Edited by: Mitchell R. 1978, John Wiley & Sons, London, 349-376.
Okabe S, Kamagata Y: Wastewater treatment. Environmental Molecular Microbiology. Edited by: Liu W. 2010, Caister Academic Press, Norfolk, UK, 191-
McHugh S, Carton M, Mahony T, O'Flaherty V: Methanogenic population structure in a variety of anaerobic bioreactors. FEMS Microbiol Lett. 2003, 219 (2): 297-304. 10.1016/S0378-1097(03)00055-7.
Bagge E, Sahlström L, Albihn A: The effect of hygienic treatment on the microbial flora of biowaste at biogas plants. Water Res. 2005, 39 (20): 4879-4886. 10.1016/j.watres.2005.03.016.
Leven L, Eriksson AR, Schnürer A: Effect of process temperature on bacterial and archaeal communities in two methanogenic bioreactors treating organic household waste. FEMS Microbiol Ecol. 2007, 59 (3): 683-693. 10.1111/j.1574-6941.2006.00263.x.
Zinder SH, Anguish T, Cardwell SC: Effects of Temperature on Methanogenesis in a Thermophilic (58 degrees C) Anaerobic Digestor. Appl Environ Microbiol. 1984, 47 (4): 808-813.
Fernandez A, Huang S, Seston S, Xing J, Hickey R, Criddle C, Tiedje J: How stable is stable? Function versus community composition. Appl Environ Microbiol. 1999, 65 (8): 3697-3704.
Jetten MSM, Stams AJM, Zehnder AJB: Acetate treshold values and acetate activating enzymes in methanogenic bacteria. FEMS Microbiol Lett. 1990, 73 (4): 339-344. 10.1111/j.1574-6968.1990.tb03958.x.
McMahon KD, Stroot PG, Mackie RI, Raskin L: Anaerobic codigestion of municipal solid waste and biosolids under various mixing conditions–II: Microbial population dynamics. Water Res. 2001, 35 (7): 1817-1827. 10.1016/S0043-1354(00)00438-3.
Goberna M, Insam H, Franke-Whittle IH: Effect of biowaste sludge maturation on the diversity of thermophilic bacteria and archaea in an anaerobic reactor. Appl Environ Microbiol. 2009, 75 (8): 2566-2572. 10.1128/AEM.02260-08.
Schnürer A, Schnürer J: Fungal survival during anaerobic digestion of organic household waste. Waste Manag. 2006, 26 (11): 1205-1211. 10.1016/j.wasman.2005.09.007.
Kymäläinen M, Lähde K, Arnold M, Kurola JM, Romantschuk M, Kautola H: Biogasification of biowaste and sewage sludge - Measurement of biogas quality. J Environ Manage. 2012, 95: S122-S127. Supplement
Münch E, Greenfield PF: Estimating VFA concentrations in prefermenters by measuring pH. Water Res. 1998, 32 (8): 2431-2441. 10.1016/S0043-1354(97)00469-7.
Koskinen K, Hultman J, Paulin L, Auvinen P, Kankaanpää H: Spatially differing bacterial communities in water columns of the northern Baltic Sea. FEMS Microbiol Ecol. 2011, 75 (1): 99-110. 10.1111/j.1574-6941.2010.00987.x.
Rincon B, Raposo F, Borja R, Gonzalez JM, Portillo MC, Saiz-Jimenez C: Performance and microbial communities of a continuous stirred tank anaerobic reactor treating two-phases olive mill solid wastes at low organic loading rates. J Biotechnol. 2006, 121 (4): 534-543. 10.1016/j.jbiotec.2005.08.013.
Ovreas L, Forney L, Daae FL, Torsvik V: Distribution of bacterioplankton in meromictic Lake Saelenvannet, as determined by denaturing gradient gel electrophoresis of PCR-amplified gene fragments coding for 16S rRNA. Appl Environ Microbiol. 1997, 63 (9): 3367-3373.
Jürgens G, Glockner F, Amann R, Saano A, Montonen L, Likolammi M, Münster U: Identification of novel Archaea in bacterioplankton of a boreal forest lake by phylogenetic analysis and fluorescent in situ hybridization(1). FEMS Microbiol Ecol. 2000, 34 (1): 45-56.
Muyzer G, de Waal EC, Uitterlinden AG: Profiling of complex microbial populations by denaturing gradient gel electrophoresis analysis of polymerase chain reaction-amplified genes coding for 16S rRNA. Appl Environ Microbiol. 1993, 59 (3): 695-700.
Edwards U, Rogall T, Blocker H, Emde M, Bottger EC: Isolation and direct complete nucleotide determination of entire genes. Characterization of a gene coding for 16S ribosomal RNA. Nucleic Acids Res. 1989, 17 (19): 7843-7853. 10.1093/nar/17.19.7843.
Turenne CY, Sanche SE, Hoban DJ, Karlowsky JA, Kabani AM: Rapid identification of fungi by using the ITS2 genetic region and an automated fluorescent capillary electrophoresis system. J Clin Microbiol. 1999, 37 (6): 1846-1851.
White TJ, Bruns T, Lee S, Taylor J: Amplification and direct sequencing of fungal ribosomal RNA genes for phylogenetics. PCR Protocols: A Guide To Methods And Applications. Edited by: Innis MA, Gelfand DH, Sninsky JJ, White TJ. 1990, Academic, New York, 315-322.
Cole JR, Wang Q, Cardenas E, Fish J, Chai B, Farris RJ, Kulam-Syed-Mohideen AS, McGarrell DM, Marsh T, Garrity GM, Tiedje JM: The Ribosomal Database Project: improved alignments and new tools for rRNA analysis. Nucleic Acids Res. 2009, 37: D141-D145. 10.1093/nar/gkn879. Database issue
Cole C, Sobala A, Lu C, Thatcher SR, Bowman A, Brown JW, Green PJ, Barton GJ, Hutvagner G: Filtering of deep sequencing data reveals the existence of abundant Dicer-dependent small RNAs derived from tRNAs. RNA. 2009, 15 (12): 2147-2160. 10.1261/rna.1738409.
Schloss PD, Westcott SL, Ryabin T, Hall JR, Hartmann M, Hollister EB, Lesniewski RA, Oakley BB, Parks DH, Robinson CJ, Sahl JW, Stres B, Thallinger GG, Van Horn DJ, Weber CF: Introducing mothur: open-source, platform-independent, community-supported software for describing and comparing microbial communities. Appl Environ Microbiol. 2009, 75 (23): 7537-7541. 10.1128/AEM.01541-09.
Pruesse E, Quast C, Knittel K, Fuchs BM, Ludwig W, Peplies J, Glockner FO: SILVA: a comprehensive online resource for quality checked and aligned ribosomal RNA sequence data compatible with ARB. Nucleic Acids Res. 2007, 35 (21): 7188-7196. 10.1093/nar/gkm864.
Chao A, Lee S: Estimating the number of classes via sample coverage. J Am Stat Assoc. 1992, 87: 210-217. 10.1080/01621459.1992.10475194.
Chao A: Nonparametric estimation of the number of classes in a population. Scand J Stat. 1984, 11: 265-270.
Magurran AE: Measuring biological diversity. 2003, Wiley-Blackwell
Yue J, Clayton M: A similarity measure based on species proportions. Commun Stat Theor M. 2005, 34: 2123-2131. 10.1080/STA-200066418.
Altschul SF, Gish W, Miller W, Myers EW, Lipman DJ: Basic local alignment search tool. J Mol Biol. 1990, 215 (3): 403-410.
Huson DH, Auch AF, Qi J, Schuster SC: MEGAN analysis of metagenomic data. Genome Res. 2007, 17 (3): 377-386. 10.1101/gr.5969107.
Zhang Z, Schwartz S, Wagner L, Miller W: A greedy algorithm for aligning DNA sequences. J Comput Biol. 2000, 7 (1–2): 203-214.
Wang Q, Garrity GM, Tiedje JM, Cole JR: Naive Bayesian classifier for rapid assignment of rRNA sequences into the new bacterial taxonomy. Appl Environ Microbiol. 2007, 73 (16): 5261-5267. 10.1128/AEM.00062-07.
Ramette A: Multivariate analyses in microbial ecology. FEMS Microbiol Ecol. 2007, 62 (2): 142-160. 10.1111/j.1574-6941.2007.00375.x.
Legendre P, Legendre L: Numerical Ecology. 1998, Elsevier, Amsterdam
Oksanen J, Blanchet FG, Kindt R, Legendre P, O'Hara RB, Simpson GL, Solymos P, Stevens MHH, Wagner H: vegan: Community Ecology Package. R package version 1.17-12. 2011, http://cran.r-project.org/package=vegan,
DeSantis TZ, Hugenholtz P, Larsen N, Rojas M, Brodie EL, Keller K, Huber T, Dalevi D, Hu P, Andersen GL: Greengenes, a chimera-checked 16S rRNA gene database and workbench compatible with ARB. Appl Environ Microbiol. 2006, 72 (7): 5069-5072. 10.1128/AEM.03006-05.
R Development Core Team: R: A language and environment for statistical computing. 2009, 2.10.1
Pages H, Aboyoun P, Gentleman R, DebRoy S, Biostrings: String objects representing biological sequences, and matching algorithms. 2009
Kibbe WA: OligoCalc: an online oligonucleotide properties calculator. Nucleic Acids Res. 2007, 35: W43-W46. 10.1093/nar/gkm234. Web Server issue
Ritari J, Paulin L, Hultman J, Auvinen P: Application of hybridization control probe to increase accuracy on ligation detection or minisequencing diagnostic microarrays. BMC Res Notes. 2009, 2: 249-10.1186/1756-0500-2-249.
Yee Hwa (Jean) Yang with contributions from Agnes Paquet and Sandrine Dudoit: marray: Exploratory analysis for two-color spotted microarray data. R package version 1.24.0. 2009
Weiss A, Jerome V, Freitag R, Mayer HK: Diversity of the resident microbiota in a thermophilic municipal biogas plant. Appl Microbiol Biotechnol. 2008, 81 (1): 163-173. 10.1007/s00253-008-1717-6.
Pycke BF, Etchebehere C, Van de Caveye P, Negroni A, Verstraete W, Boon N: A time-course analysis of four full-scale anaerobic digesters in relation to the dynamics of change of their microbial communities. Water Sci Technol. 2011, 63 (4): 769-775. 10.2166/wst.2011.307.
Martin-Gonzalez L, Castro R, Pereira MA, Alves MM, Font X, Vicent T: Thermophilic co-digestion of organic fraction of municipal solid wastes with FOG wastes from a sewage treatment plant: reactor performance and microbial community monitoring. Bioresour Technol. 2011, 102 (7): 4734-4741. 10.1016/j.biortech.2011.01.060.
Hernon F, Forbes C, Colleran E: Identification of mesophilic and thermophilic fermentative species in anaerobic granular sludge. Water Sci Technol. 2006, 54 (2): 19-24. 10.2166/wst.2006.481.
Ariesyady HD, Ito T, Okabe S: Functional bacterial and archaeal community structures of major trophic groups in a full-scale anaerobic sludge digester. Water Res. 2007, 41 (7): 1554-1568. 10.1016/j.watres.2006.12.036.
Sekiguchi Y, Imachi H, Susilorukmi A, Muramatsu M, Ohashi A, Harada H, Hanada S, Kamagata Y: Tepidanaerobacter syntrophicus gen. nov., sp. nov., an anaerobic, moderately thermophilic, syntrophic alcohol- and lactate-degrading bacterium isolated from thermophilic digested sludges. Int J Syst Evol Microbiol. 2006, 56 (Pt 7): 1621-1629.
Sneath PHA, Sokal RR: Numerical taxonomy: the principles and practice of numerical classification. 1973, W.H. Freeman and Company, San Francisco
Godon JJ, Zumstein E, Dabert P, Habouzit F, Moletta R: Molecular microbial diversity of an anaerobic digestor as determined by small-subunit rDNA sequence analysis. Appl Environ Microbiol. 1997, 63 (7): 2802-2813.
von Wintzingerode F, Selent B, Hegemann W, Göbel UB: Phylogenetic analysis of an anaerobic, trichlorobenzene-transforming microbial consortium. Appl Environ Microbiol. 1999, 65 (1): 283-286.
Wu J, Liu W, Tseng I, Cheng S: Characterization of a 4-methylbenzoate-degrading methanogenic consortium as determined by small-subunit rDNA sequence analysis. J Biosci Bioeng. 2001, 91 (5): 449-455.
Sekiguchi Y, Kamagata Y, Syutsubo K, Ohashi A, Harada H, Nakamura K: Phylogenetic diversity of mesophilic and thermophilic granular sludges determined by 16S rRNA gene analysis. Microbiology. 1998, 144 (Pt 9): 2655-2665.
Madigan M, Martinko J, Dunlop P, Clark D: Brock Biology of Microorganisms 12th ed. 2009, Pearson Prentice Hall
Krause L, Diaz NN, Edwards RA, Gartemann KH, Krömeke H, Neuweger H, Pühler A, Runte KJ, Schlüter A, Stoye J, Szczepanowski R, Tauch A, Goesmann A: Taxonomic composition and gene content of a methane-producing microbial community isolated from a biogas reactor. J Biotechnol. 2008, 136 (1–2): 91-101.
Liu FH, Wang SB, Zhang JS, Zhang J, Yan X, Zhou HK, Zhao GP, Zhou ZH: The structure of the bacterial and archaeal community in a biogas digester as revealed by denaturing gradient gel electrophoresis and 16S rDNA sequencing analysis. J Appl Microbiol. 2009, 106 (3): 952-966. 10.1111/j.1365-2672.2008.04064.x.
Klocke M, Mähnert P, Mundt K, Souidi K, Linke B: Microbial community analysis of a biogas-producing completely stirred tank reactor fed continuously with fodder beet silage as mono-substrate. Syst Appl Microbiol. 2007, 30 (2): 139-151. 10.1016/j.syapm.2006.03.007.
Riviere D, Desvignes V, Pelletier E, Chaussonnerie S, Guermazi S, Weissenbach J, Li T, Camacho P, Sghir A: Towards the definition of a core of microorganisms involved in anaerobic digestion of sludge. ISME J. 2009, 3 (6): 700-714. 10.1038/ismej.2009.2.
Goberna M, Gadermaier M, García C, Wett B, Insam H: Adaptation of methanogenic communities to the cofermentation of cattle excreta and olive mill wastes at 37°C and 55°C. Appl Environ Microbiol. 2010, 19: 6564-6571.
Hultman J, Vasara T, Partanen P, Kurola J, Kontro MH, Paulin L, Auvinen P, Romantschuk M: Determination of fungal succession during municipal solid waste composting using a cloning-based analysis. J Appl Microbiol. 2010, 108 (2): 472-487. 10.1111/j.1365-2672.2009.04439.x.
Jennings DH: The physiology of fungal nutrition. 1995, Cambridge University Press, Cambridge, United Kingdom
Kinsey G, Paterson R, Kelley J: Filamentous fungi in water systems. The Handbook of Water and Wastewater Microbiology. Edited by: Mara D. 2003, Academic, HN, 77-819.
Dumitru R, Hornby JM, Nickerson KW: Defined Anaerobic Growth Medium for Studying Candida albicans Basic Biology and Resistance to Eight Antifungal Drugs. Antimicrob Agents Chemother. 2004, 48 (7): 2350-2354. 10.1128/AAC.48.7.2350-2354.2004.
Franke-Whittle IH, Goberna M, Pfister V, Insam H: Design and development of the ANAEROCHIP microarray for investigation of methanogenic communities. J Microbiol Methods. 2009, 79 (3): 279-288. 10.1016/j.mimet.2009.09.017.
Candela M, Consolandi C, Severgnini M, Biagi E, Castiglioni B, Vitali B, De Bellis G, Brigidi P: High taxonomic level fingerprint of the human intestinal microbiota by ligase detection reaction–universal array approach. BMC Microbiol. 2010, 10: 116-10.1186/1471-2180-10-116.
Hultman J, Ritari J, Romantschuk M, Paulin L, Auvinen P: Universal ligation-detection-reaction microarray applied for compost microbes. BMC Microbiol. 2008, 8: 237-10.1186/1471-2180-8-237.
van Doorn R, Szemes M, Bonants P, Kowalchuk GA, Salles JF, Ortenberg E, Schoen CD: Quantitative multiplex detection of plant pathogens using a novel ligation probe-based system coupled with universal, high-throughput real-time PCR on OpenArrays. BMC Genomics. 2007, 8: 276-10.1186/1471-2164-8-276.
Szemes M, Bonants P, de Weerdt M, Baner J, Landegren U, Schoen CD: Diagnostic application of padlock probes–multiplex detection of plant pathogens using universal microarrays. Nucleic Acids Res. 2005, 33 (8): e70-10.1093/nar/gni069.
Li JB, Gao Y, Aach J, Zhang K, Kryukov GV, Xie B, Ahlford A, Yoon JK, Rosenbaum AM, Zaranek AW, LeProust E, Sunyaev SR, Church GM: Multiplex padlock targeted sequencing reveals human hypermutable CpG variations. Genome Res. 2009, 19 (9): 1606-1615. 10.1101/gr.092213.109.
Hardenbol P, Yu F, Belmont J, Mackenzie J, Bruckner C, Brundage T, Boudreau A, Chow S, Eberle J, Erbilgin A, Falkowski M, Fitzgerald R, Ghose S, Iartchouk O, Jain M, Karlin-Neumann G, Lu X, Miao X, Moore B, Moorhead M, Namsaraev E, Pasternak S, Prakash E, Tran K, Wang Z, Jones HB, Davis RW, Willis TD, Gibbs RA: Highly multiplexed molecular inversion probe genotyping: over 10,000 targeted SNPs genotyped in a single tube assay. Genome Res. 2005, 15 (2): 269-275. 10.1101/gr.3185605.
Mutter GL, Boynton KA: PCR bias in amplification of androgen receptor alleles, a trinucleotide repeat marker used in clonality studies. Nucleic Acids Res. 1995, 23 (8): 1411-1418. 10.1093/nar/23.8.1411.
Housby JN, Southern EM: Fidelity of DNA ligation: a novel experimental approach based on the polymerisation of libraries of oligonucleotides. Nucleic Acids Res. 1998, 26 (18): 4259-4266. 10.1093/nar/26.18.4259.
Faulhammer D, Lipton RJ, Landweber LF: Fidelity of enzymatic ligation for DNA computing. J Comput Biol. 2000, 7 (6): 839-848. 10.1089/10665270050514963.
Dixon MT, Hillis DM: Ribosomal RNA secondary structure: compensatory mutations and implications for phylogenetic analysis. Mol Biol Evol. 1993, 10 (1): 256-267.
This work was supported financially by Maj and Tor Nessling Foundation, Finland and the Finnish National Technology Agency (Tekes) ADOPT project (40080/07). PA and MR were funded by the European Regional Development Fund (YMLI project).
The authors declare that they have no competing interests.
MK, MR and JMK conceived the experimental design on anaerobic digestion. PA, LP, JH, JR and KK conceived the microarray and sequencing experiments. MK provided expertise on physical and chemical processes of digestion. JR performed the microarray and qPCR experiments and analysed the data. KK performed the PCRs for amplicon sequencing and analysed the sequence data. JR and KK did the RDA analysis and drafted the manuscript. All authors contributed to writing the manuscript and read and approved the final version.
Jarmo Ritari, Kaisa Koskinen contributed equally to this work.
Electronic supplementary material
About this article
Cite this article
Ritari, J., Koskinen, K., Hultman, J. et al. Molecular analysis of meso- and thermophilic microbiota associated with anaerobic biowaste degradation. BMC Microbiol 12, 121 (2012) doi:10.1186/1471-2180-12-121
- Anaerobic Digestion
- Fungal Community
- Biogas Production
- Anaerobic Digestion Process
- Fungal Sequence